Skip to content

Garment Quality Inspection: AQL, Defects and Inspection Stages Explained

How garment inspection works from quality plan to final AQL inspection: defect classes, measurement tolerances, packing checks, lab testing and reading the report.

Updated
Updated 18 Nov 2026
Reading time
10 min read
Hands holding hang tags at the neckline of a light grey sweatshirt

Garment quality inspection is a sequence of checks, not a single event at the end of production. The final AQL inspection decides whether a shipment is released, but most quality is won or lost earlier: in the approved sample, the pre-production meeting and the first days on the sewing line.

This guide explains how a practical inspection program fits together, how AQL sampling works under ISO 2859-1 and ANSI/ASQ Z1.4, how defects are classified, what inspectors check beyond workmanship, and how to read an inspection report and act on it. It is written for buyers who commission inspections through their own staff, a third-party inspection company or a sourcing partner.

Key takeaways

  • Quality is controlled across stages (pre-production meeting, inline, during production and final inspection), not only before shipment.
  • Final random inspections commonly use ISO 2859-1 or ANSI/ASQ Z1.4 sampling at general inspection level II.
  • A common, not mandatory, choice is critical defects not allowed, AQL 2.5 for major and AQL 4.0 for minor defects.
  • Inspection is sample-based and largely visual; lab testing verifies performance and chemical compliance, and most programs need both.
  • Write the quality plan before production, including what happens after a failed inspection.

Write a quality plan before production starts

A quality plan turns 'good quality' into criteria an inspector can check. Agree it with the factory before cutting and reference it in the purchase order. Our quality inspection service starts from the same document.

Reference standards
Tech pack version, approved PP sample, lab dips, strike-offs, trim cards and wash standard. Keep signed or sealed reference samples at the factory, since bulk is judged against them.
Measurement specification
Points of measure per size with tolerances, and which points are critical to fit.
Inspection stages
Which inspections will run (inline, during production, final), who performs them and at what point in production.
Sampling and acceptance criteria
Sampling standard, inspection level, AQL per defect class and how critical defects are handled.
Defect list
Your definitions of critical, major and minor defects for this product, ideally with photos, so classification is consistent between inspectors.
Testing requirements
Fabric and garment tests, methods, pass criteria and the nominated lab. The fabric guide lists common tests.
Packing and failure procedure
Packing and labeling requirements, plus what happens after a failure: rework, re-inspection, who pays re-inspection fees and who approves release.

Inspection stages from pre-production to shipment

Each stage catches a different type of problem. Earlier checks are cheaper because defects found before cutting or during sewing can be fixed at the source.

  1. 01

    Pre-production meeting (PPM)

    Held before cutting with the factory's merchandising, production and quality teams. Review the PP sample and comments, fabric and trim approvals, test results, critical operations, measurement points and packing. Record agreed actions in signed minutes.

  2. 02

    Material and first-cut checks

    Check bulk fabric for shade, weight, width and visible faults, trims against trim cards, and first cut panels against patterns. Fabric rolls are commonly graded with a point-based system such as the four-point system.

  3. 03

    Inline inspection

    Quality staff check work at sewing operations during the first days of output, so recurring faults such as wrong stitch density or uneven seams are corrected early.

  4. 04

    During-production inspection (DUPRO)

    A sample-based inspection once a meaningful share of goods is finished, covering workmanship, measurements and early packed goods. Useful for large orders, new factories and new styles.

  5. 05

    Final random inspection (FRI) or pre-shipment inspection

    Performed when production is complete and most goods, commonly at least 80%, are packed. Cartons are selected at random and garments sampled by AQL. The result usually decides shipment release.

  6. 06

    Container loading check (optional)

    Verifies carton count, condition and loading, and confirms that the inspected goods are the ones shipped.

How AQL sampling works

AQL sampling decides whether to accept a lot by inspecting a random sample whose size is set by the lot size. Most garment inspections use ISO 2859-1 or its US counterpart ANSI/ASQ Z1.4, which are closely aligned for single sampling plans.

The plan has four inputs:

  1. Lot size: the number of pieces in the inspection lot.
  2. Inspection level: general level II is commonly used for garments. Levels I and III give smaller or larger samples, and special levels S-1 to S-4 are used where checks are slow or destructive, such as some measurement or functional tests.
  3. Sample size code letter: read from the standard's table using lot size and inspection level, then converted to a sample size.
  4. AQL (acceptance quality limit): set separately for each defect class. Each AQL gives an acceptance number (Ac) and a rejection number (Re) for the sample size.

If the defects found in a class are at or below Ac, that class passes; if they reach Re, it fails. The lot passes only if every class passes. Many buyers choose critical defects not allowed, AQL 2.5 for major defects and AQL 4.0 for minor defects. This is common practice, not a requirement of the standard; some premium programs use tighter levels such as 1.5 for major defects.

AQL sampling extract: general level II, single sampling, normal inspection

The extract shows common lot sizes and the resulting acceptance and rejection numbers at AQL 2.5 and 4.0. Use the current edition of the standard for real inspections; switching rules (tightened or reduced inspection) can change the plan over a series of lots.

Ac = maximum defects in the sample for acceptance; Re = defect count at which the class fails. Simplified extract; verify against ISO 2859-1 or ANSI/ASQ Z1.4.
Lot size (pieces)Code letterSample sizeAQL 2.5 major (Ac / Re)AQL 4.0 minor (Ac / Re)
151–280G322 / 33 / 4
281–500H503 / 45 / 6
501–1,200J805 / 67 / 8
1,201–3,200K1257 / 810 / 11
3,201–10,000L20010 / 1114 / 15
10,001–35,000M31514 / 1521 / 22

What an AQL result does and does not tell you

AQL sampling accepts or rejects a lot on the evidence of a random sample. A pass means the sample met the agreed limits; it does not mean every garment in the lot is free of defects. A lot whose true defect level sits near the AQL can pass or fail depending on which pieces are drawn.

For safety-related risks, buyers commonly treat critical defects as not allowed in the sample and add full checks on top of sampling, such as needle detection for babywear. Agree AQL levels and sample sizes before the inspection and do not change them after seeing results.

Defect classification: critical, major and minor

Defects are classified by their consequence for the user and the buyer, not by how they look. Agree definitions in advance so that the same fault is classified the same way at every inspection.

Examples only. Your defect list and the product's end use, such as babywear, determine the final classification.
ClassDefinitionTypical garment examplesCommon practice
CriticalLikely to cause harm to the user, or breaches a legal or safety requirement.Broken needle or metal fragment, sharp trim edges, insecure small parts or non-compliant drawstrings on childrenswear, mold.Commonly not allowed; any critical defect found fails the lot.
MajorLikely to cause product failure, reduce usability or lead to a customer return.Open seams, broken stitches, holes, wrong size label, measurements out of tolerance, shade variation between panels, visible stains, misplaced print.AQL 2.5 is a common choice; premium programs may go tighter.
MinorA departure from the standard unlikely to affect use or cause a return.Untrimmed threads, slightly uneven stitching, minor puckering, small marks not visible in normal wear.AQL 4.0 is a common choice.

On-site checks beyond workmanship

A full final inspection covers more than visual defects. Inspectors typically also check quantity, measurements, labeling, packing and a set of simple on-site tests.

Quantity and assortment
Count packed and unpacked goods against the PO by style, color and size, and confirm carton assortment (solid or ratio packing).
Measurements and tolerances
Measure a sample per size and color against the spec sheet, focusing on critical points such as chest, length, waist and inseam. Tolerances come from the spec sheet and are commonly tighter for small points, such as neck opening, than for body length. Record how far each reading is out.
Comparison with approved samples
Check style, color, fabric, hand feel, print and embroidery against the approved PP sample under the agreed light source.
Labels and barcodes
Main, size, care, fiber content and origin labels, hangtags, and barcode scans to confirm codes read and match size and color.
Packing and cartons
Folding, polybags and any required suffocation warnings, carton dimensions and weight, shipping marks and carton condition. A carton drop test is commonly performed.
Functional and on-site tests
Common checks include a rub test for color transfer, seam pull tests, zipper and snap function, fabric weight, and moisture readings where humidity is a risk.
Needle and metal detection
For babywear, childrenswear and some markets, buyers commonly require every packed piece to pass a metal detector in addition to sampling.

Lab testing vs inspection: what each covers

Inspection confirms that goods look, measure and are packed as approved; lab testing confirms that they perform and comply as required. Most programs need both, planned at different points.

AspectInspectionLab testing
Main questionDo the goods match the approved sample, spec and packing instructions?Do fabric and garments meet performance and chemical requirements?
MethodVisual checks, measurement and simple on-site tests on a random sample.Standardized ISO, AATCC, ASTM or other methods on submitted or drawn samples.
Typical scopeWorkmanship, measurements, labeling, packing, quantity.Shrinkage, colorfastness, pilling, strength, fiber content, restricted substances.
TimingInline, during production and before shipment.Fabric before cutting; garments at PP or bulk stage.
Who performs itBuyer QC staff, a sourcing partner or a third-party inspection company.An independent laboratory, commonly accredited to ISO/IEC 17025.
Regulatory roleConfirms required labels and warnings are present.Supports compliance with rules such as EU REACH or US CPSIA requirements for children's products; verify current requirements with the official source.

How to read an inspection report and act on it

An inspection report is a decision document. Read it in this order, then decide whether to release, hold or rework the goods.

  1. 01

    Check the result and scope

    Note the overall result (pass, fail or pending buyer decision) and confirm the report covers the right PO, styles, colors and quantities.

  2. 02

    Confirm the sampling plan

    Lot size, inspection level, sample size and AQL should match the quality plan. A wrong sample size undermines the result.

  3. 03

    Review defects by class

    Compare defects found with the acceptance numbers. One recurring defect points to a process problem; many scattered defects point to general workmanship.

  4. 04

    Review measurements, tests and photos

    Look for points consistently out of tolerance, failed on-site tests and photos showing severity. Inspector comments often explain borderline calls.

  5. 05

    Decide and document

    Release, hold or require rework. After a fail, the usual path is sorting and rework, then re-inspection under the same plan. Accepting a failed lot should be a documented commercial decision.

  6. 06

    Close the loop with corrective action

    Ask the factory for root-cause analysis and corrective and preventive actions (CAPA), such as retraining an operation, adjusting a machine or adding an inline check, and verify them at the next inspection.

Frequently asked questions

What does AQL 2.5 mean in garment inspection?

It is the acceptance quality limit used to select the sampling plan for a defect class, usually major defects. For a lot of 3,201 to 10,000 pieces at general level II, the sample is 200 pieces, accepted with up to 10 major defects and rejected at 11. It does not certify that the lot contains 2.5% defects or fewer.

When should a final random inspection be scheduled?

When production is complete and most goods, commonly at least 80%, are packed. Book it several days ahead and leave time before the vessel cut-off for rework and re-inspection if needed.

What is the difference between inline inspection and DUPRO?

Inline inspection checks work at sewing operations as it happens, to correct processes early. A DUPRO is a sample-based inspection of finished goods partway through production, reported much like a final inspection.

Do I need lab testing if I already run AQL inspections?

Usually yes. Inspection cannot verify shrinkage, colorfastness, fiber content or restricted substances; those need laboratory tests to recognized methods.

Who pays for re-inspection after a failure?

It is a commercial term, so agree it in the quality plan or PO. A common arrangement is that the factory pays re-inspection costs after a failed inspection. See the garment sourcing guide for linking quality to payment terms.

Sources and references

Regulations, tariffs and preference schemes change. Always confirm current requirements with the official source or a licensed customs broker.

Related guides

Related products and services

Markets

Ready to source garments from Bangladesh?

Tell us what you need. We review every enquiry personally and reply with next steps, questions or factory options.

Request a Quote